NS-EN 1455-1:1999

NOK 787,00 (eks. mva) InformationOvervåk standarden
basket Skriv ut på papir basket Trykket og innbundet
Få nettbasert tilgang
Status: Alert Tilbaketrukket
Norsk tittel: Rørledninger av plast for bortledning av avløpsvann (lav og høy temperatur) i bygninger — Akrylnitril-butadien-styren (ABS) — Del 1: Krav til rør, rørdeler og system
Engelsk tittel: Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure — Acrylonitrile-butadiene-styrene (ABS) — Part 1: Requirements for pipes, fittings and the system
Varetype: Standard
Språk: Engelsk
Utgave: 1 (1999-11-10)
Erstattes av: NS-EN 1455-1:2022 Check Gyldig
Antall sider: 40
Pris:

NOK 787,00 (eks. mva)
NOK 983,75 (ink. mva)

Inkludert i: NS ICS 23
NS ICS 23.040
NS ICS 23.040.01
NS ICS 83.140
NS ICS 91 - Bygningsmaterialer og bygging
NS ICS 91.140
NS ICS 91.140.80
NS ICS 83
NS ICS 83.140.30
Omfang: This European standard specifies the requirements for pipes, fittings and the system of acrylonitrile-butadiene- styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) solid-wall piping systems in the field of soil and waste discharge (low and high temperature) - inside buildings (marked with "B") - for both inside buildings and buried in ground within the building structure (marked with "BD"). NOTE 1 The application area "inside buildings" according to this standard, applies to the interior area of the building only. The application area "within the building structure" conforms to the requirements for "inside buildings" according to prEN 12056-1. It also specifies the test parameters for the test methods referred to in this standard. This standard is applicable to ABS pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following purposes: a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature); b) ventilation pipework associated with a); c) rainwater pipework within the building structure. It applies to pipes and fittings, marked with "B", which are intended to be used inside buildings and outside buildings fixed onto the wall. It applies to pipes and fittings, marked with "BD", which are intended to be used for both inside buildings and buried in ground within the building structure. NOTE 2 Only components (marked with "BD" ) are intended for use buried in ground within the building structure with a nominal ring stiffness of at least SN 4 and nominal outside diameters equal to or greater than 75 mm. NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area "B" only. This standard is applicable to ABS pipes and fittings of the following types: - plain-ended, - with integral elastomeric ring seal socket, - with integral solvent cement socket, - with integral dual purpose socket for elastomeric ring seal joints and/or solvent cement joints, whereby the fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 4 Components conforming to any of the System Standards listed in Annex B (informative) can be used with pipes and fittings conforming to this standard, provided they conform to the requirements for joint dimensions and to the functional requirements given in this standard. This standard covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours. NOTE 5 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices codes.
Komité: SN/K 084
Fastsatt: 1999-11-10
Tilbaketrukket: 2022-12-20
ICS: 23.040.01 - Rørdeler og rørledninger generelt
83.140.30 - Plastrør, - deler og -ventiler
91.140.80 - Avløpssystemer