ISO 13628-5:2009

Standard
NOK 3 211,00 (eks. mva) InformationOvervåk standarden
basket Skriv ut på papir basket Trykket og innbundet
Få nettbasert tilgang
Status: Check Gyldig
Norsk tittel: Petroleum and natural gas industries — Design and operation of subsea production systems — Part 5: Subsea umbilicals
Engelsk tittel: Petroleum and natural gas industries — Design and operation of subsea production systems — Part 5: Subsea umbilicals
Varetype: Standard
Språk: Engelsk
Utgave: 2 (2009-12-11)
Erstatter: ISO 13628-5:2002 Alert Tilbaketrukket
Antall sider: 168
Pris:

NOK 3 211,00 (eks. mva)
NOK 4 013,75 (ink. mva)

Omfang: <p>This part of <std std-id="iso:std:iso:13628:en" type="undated"><std-ref>ISO 13628</std-ref></std> specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include topside hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.</p><p>This part of <std std-id="iso:std:iso:13628:en" type="undated"><std-ref>ISO 13628</std-ref></std> applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination.</p><p>This part of <std std-id="iso:std:iso:13628:en" type="undated"><std-ref>ISO 13628</std-ref></std> applies to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings.</p><p>This part of <std std-id="iso:std:iso:13628:en" type="undated"><std-ref>ISO 13628</std-ref></std> does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.</p><p>This part of <std std-id="iso:std:iso:13628:en" type="undated"><std-ref>ISO 13628</std-ref></std> applies only to tubes with the following dimensions: wall thickness, <italic><styled-content style="font-family:Times New Roman">t</styled-content></italic> &gt; 6 mm, internal diameter, ID &gt; 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.</p><p>This part of <std std-id="iso:std:iso:13628:en" type="undated"><std-ref>ISO 13628</std-ref></std> does not apply to a tube or hose rated lower than 7 MPa (1 015 psi).</p><p>This part of <std std-id="iso:std:iso:13628:en" type="undated"><std-ref>ISO 13628</std-ref></std> does not apply to electric cable voltage ratings above standard rated voltages <italic>U</italic><sub>0</sub>/<italic>U</italic>(<italic>U</italic><sub>m</sub>) = 3,6/6(7,2) kV rms, where <italic>U</italic><sub>0</sub>, <italic>U</italic> and <italic>U</italic><sub>m</sub> are as defined in <std><std-ref>IEC 60502-1</std-ref></std> and <std><std-ref>IEC 60502-2</std-ref></std>.</p>
Fastsatt: 2009-12-11
ICS: 75.180.10 - Utstyr for leting og utvinning